How To Clean Hi Point 9mm

GET THE C9 Here

Ohio-based Hi-Point has been delivering an assortment of pistols and carbines to the consumer market since 1994 but they can be somewhat hard to clean and disassemble.

To requite the word direct from the company, Mike Strassell, Hullo-Signal's owner, goes for a deep dive on the inner workings of the C9 series 9mm pistol in the beneath 21-infinitesimal video. The instruction also helps those with a Hi-Point CF380 or CF380 Comp model as the full disassembly and assembly process is the same.

While non every bit like shooting fish in a barrel equally maintaining a modern revolver or something similar, say a Glock, the chore of breaking the C9 down to its component pieces isn't rocket science. Strassell does point out that those electing to tackle the job need to beginning with an unloaded pistol, empty mag, a multifariousness of punches (3/32, i/8, 1/16) a block, contrasted screwdrivers, the adjustment tool that comes with the gun, and a small hammer.

As for cleaning once the handgun is disassembled, HI-Point notes in their recently updated user's manual for the C380/C9 the following process:

Butt: Make clean the barrel as follows:
1. Wet a cleaning patch with a gun cleaning solvent or a cleaner-lubricant- preservative and run it through the barrel, from the sleeping accommodation terminate, several times using a cleaning rod.

2. Wet a bristled cleaning brush with gun cleaning solvent or a cleaner-lubricant preservative and run it back and forth in the barrel, from the chamber end, using a cleaning rod.

3. Wet a new cleaning patch with gun oil or a cleaner-lubricant-preservative and run it through the barrel once, from the chamber cease, with the cleaning rod and examine it. If information technology is not clean, echo steps 2 and 3 until the patch remains clean afterward beingness run through the barrel.

iv. Before firing your Hi-Indicate pistol, run a clean patch through the butt, from the chamber end, using the cleaning rod. Repeat this process until the patch comes out of the barrel with no gun oil or cleaner-lubricant-preservative on it. (Notation: If y'all will be storing your Hi-Point pistol, do non perform step 4 until you are ready to use it).

5. Moisture a nylon bristle brush with gun cleaning solvent or a cleaner-lubricant-preservative and thoroughly brush the outside of the barrel to remove any clay or residue.

vi. Wipe the outside of the barrel dry with a clean patch and examine information technology. If information technology is non clean, repeat steps 5 and 6 until the patch remains clean.

SLIDE: Make clean the slide equally follows:

one. Wet a nylon bristle brush with gun cleaning solvent or a cleaner-lubricant-preservative and thoroughly brush the bottom surfaces where the slide sits on the frame.

2. Wipe the bottom surfaces where the slide sits on the frame with a clean patch and examine it. If information technology is non clean, echo steps 1 and 2 until the patch remains make clean.

3. Wet a nylon bristle brush with gun oil or a cleaner-lubricant-preservative and, while belongings the slide with the cage end facing down, brush the breech face and the surface area nether the extractor. Do not employ solvents on hydro dipped coated surfaces.

4. While holding the slide with the cage end facing downward, wipe the breech face with a clean patch and examine it. If it is not clean, repeat steps 3 and iv until the patch remains clean.

5. Cheque all other exposed areas of the slide for cleanliness. If whatsoever dirt or droppings is found, remove it with gun cleaning solvent or a cleaner-lubricant-preservative using a nylon bristle castor or a clean patch.

half-dozen. Wipe the exposed areas of the slide that you lot have cleaned in step 5 with a clean patch and examine it. If it is not clean, repeat steps 5 and 6 until the patch remains clean.

FRAME: Check the frame for cleanliness. If necessary, make clean the frame equally follows:

1. Wipe exposed parts of the frame with a clean patch that has been slightly dampened with gun cleaning solvent or a cleaner-lubricant- preservative.

ii. Wipe the exposed areas of the frame with a clean patch and examine information technology. If it is non clean, repeat steps i and ii until the patch remains clean.

Mag: Inspect the magazine for dirt or visible damage. If necessary, clean the magazine as follows:

1. Wipe the outside of the magazine and the feed lips with a clean patch that has been slightly dampened with gun cleaning solvent or a cleaner-lubricant-preservative.

2. Wipe the outside of the magazine and the feed lips with a clean patch and examine it. If it is non clean, echo steps ane and 2 until the patch remains clean.

Afterward you have cleaned your Hi-Bespeak pistol, lubricate it by slightly dampening a clean patch with gun oil or a cleaner-lubricant-preservative and wiping the outside of the barrel, the within of the slide and the outside of the magazine.

Your How-do-you-do-Bespeak pistol is designed to operate properly with only a pocket-size corporeality of lubrication. Do non over lubricate your How-do-you-do-Point pistol because also much lubricant can collect unburned pulverisation and other droppings and prevent your Hullo-Point pistol from performance properly.

After you have finished cleaning and lubricating your How-do-you-do-Signal pistol, and before you assemble it, yous should inspect the barrel for lead build-upwardly, bulges, cracks or obstructions and audit the frame and slide for any corrosion or any visible harm.

In the video on disassembly, when switching to assembly, Strassell warns on what parts not to adjust — such equally the drop safety counterweight — and reiterates Hi-Bespeak's assurances that, should the user observe broken or damaged parts, the mill will "send out replacement parts for free."

Also, Hi-Point reached out and wanted united states of america to share this cautionary tale about the above video:

"This video shows how to completely disassemble (detail strip) the C-9 pistol and is intended for utilize by trained armorers/gunsmiths only. Users should never detach their C-nine pistols beyond the instructions in the Instruction transmission. Further disassembly by untrained persons could crusade your Hullo-Point pistol to malfunction and will void the warranty. Hi-Point pistols are covered by a lifetime warranty. If your C-9 pistol is non functioning properly, needs to have a worn or cleaved part replaced, or its internal components need to be cleaned (which is not normally necessary) please contact Strassell's Machine, Inc. or a qualified gunsmith."

According to statistics by federal regulators, Hi-Indicate produced 14,805 semi-automatic .380-caliber pistols in 2017 along with some other 31,210 chambered in 9mm, all backed up by a lifetime warranty.

The company made headlines across the greater gun community this year, first with their new 2nd generation C9 pistol, to be named the YC9 "Yeet Cannon" afterwards the results of an online public poll. In celebration of the public outpouring, Hi-Betoken has also released a special version of the C9 dubbed the "Yeet Cannon G1."

The original C9 is at present considered past many to be the Gen 1 Yeet Cannon

Source: https://www.guns.com/news/2019/08/23/the-secret-to-hi-point-c9-cleaning-disassembly-revealed

Share this post